Saral, D., & K枚se, E., (2024).
Academic Studies on Fishing Vessels in Turkey
Ocean Engineering, vol.308, 1-17.听听听听听听听听听听听听听听听
Pehlivan, E. F., & Alt谋n, 陌., (2024).
Exergy Analysis Under Consideration of Operational Parameters by Numerical Approach in A Two-Stroke Marine Diesel Engine
Fuel, vol.368.
Erkurtulmu艧, S. A., & Pe艧man, E., (2024).
GIS-Based Floating Offshore Wind Turbine Installation Site Selection Using Fuzzy Analytic Hierarchy Process in Northeast Aegean Sea
Brodogradnja, vol.75, no.2, 1-21.
Pesman, E., Copuroglu, H. 陌., & Katayama, T., (2024).
The Effect of a Ship's Acceleration and Deceleration on Parametric Roll Motion In Regular Head Waves At Resonance Conditions
Ocean Engineering, vol.291.听听听听听听听听听听听听听听听
Sara莽, B., Demirta艧, C., & Ayhan, T., (2024).
Thermodynamic Analysis of Drying Cycles Utilizing A Desiccant Wheel Thermoelectric Modules And Heat Pipe For The Drying Of Hazel Nuts In The East Blacksea Climatic Conditions听
Journal of Thermal Analysis and Calorimetry, vol.1, no.1, 1-2.听听听听听听听听听听听听听听听
Sara莽, B., Aksu, E., Demirta艧, C., & Ayhan, T., (2024).
Free Convection Heat Transfer and Buoyancy-Assisted Flow Over A Heated Plate Inserted Horizontally In A Vertical Channel With Time-Varying Conditions
Journal of Thermal Analysis and Calorimetry, vol.149, no.5, 2255-2271.听听听听听听听听听听听听听听听
脟olak, K., 脰lmez, H., & Sara莽, B., (2024).
Waste Heat Recovery Assessment of Triple Heat-Exchanger Usage for Ship Main Engine Pre-Heating and Freshwater Generation Systems
Proceedings Of the Institution of Mechanical Engineers Part M-Journal of Engineering for The Maritime Environment, vol.238, no.1, 209-230.
Saral, D., & K枚se, E., (2023).
A Non-Dimensional Offset Table for The Black Sea Type Fishing Vessels
Applied Ocean Research, vol.139.
艦ener, M. Z., Yoon, H. K., Nguyen, T. T. D., Park, J., & K枚se, E., (2023).
An Experimental Study on Capacitive and Ultrasonic Measurement Principles and Uncertainty Assessment in Laboratory Wave Measurements
Ocean Engineering, vol.285.
听听
艦ahin, 脰. S., Kahramanoglu, E., 脟akici, F., & Pe艧man, E., (2023).
Control Of Dynamic Trim for Planing Vessels with Interceptors in Terms of Comfort and Minimum Drag
Brodogradnja, vol.74, no.1, 1-17.
听听听听听听听
Tuti, M., 艦ahin, Z., & Durgun, O., (2023).
Experimental Investigation of The Effects of Water Addition into The Intake Air on Combustion Parameters, Energy Balance And Developing An Empirical Combustion Duration Relation In Automobile Diesel Engine
Journal of Thermal Science and Technology, vol.43, no.2, 217-232.
听听听听听听听听听听听听听听听
Okur, O., K眉莽眉k, H., & Midilli, A., (2023).
Triple-Effect New Generation Drying Technique.
Innovative Food Science and Emerging Technologies, vol.89.听听听听听听听听听听听听听听听
Midilli, A., & Kucuk, H., (2023).
Development Of a New Curve Equation Representing Thin Layer Drying Process
Energy Sources Part A-Recovery Utilization and Environmental Effects, vol.45, no.4, 9717-9730.
Ugurlu, O., K枚se, E., Ba艧ar, E., 脰zk枚k, M., & Wang, J., (2022).
Simulation Modelling of Chief Officers' Working Hours on Short Sea Shipping
Ships And Offshore Structures, Vol.17, No.6, 1312-1320.
T眉rk, A., G眉rgen, S., 脰zk枚k, M., & Alt谋n, 陌., (2022).
A Comprehensive Investigation into The Performance of Genetic Algorithm for Effective Shipyard Topological Layout
Proceedings Of the Institution of Mechanical Engineers Part M-Journal of Engineering for The Maritime Environment, vol.236, no.3, 726-740.
K枚se, S., Sekban, D. M., & 脰zk枚k, M., (2022).
Determination Of Port-Induced Exhaust Gas Emission Amounts and Investigation of Environmental Impact by Creating Emission Maps: Sample of Trabzon Port
International Journal of Sustainable Transportation, vol.16, no.3, 258-268.
G眉rgen, S., & Altin, 陌., (2022).
Novel Decision-Making Strategy for Working Fluid Selection in Organic Rankine Cycle: A Case Study for Waste Heat Recovery of a Marine Diesel Engine
Energy, vol.252.
听听听听听听听听听
G眉rgen, S., Kahraman, H. T., Aras, S., & Alt谋n, 陌., (2022).
A Comprehensive Performance Analysis of Meta-Heuristic Optimization Techniques for Effective Organic Rankine Cycle Design
Applied Thermal Engineering, vol.213.
听听听听听听听听听听听听听听听
脟opuro臒lu, H. 陌., & Pe艧man, E., (2022).
Ship Staff Wind Comfort and Wind Safety in The Walkways of Containerships and Case Study For A Feeder Containership听
Ships And Offshore Structures, vol.17, no.4, 920-938.
艦ener, M. Z., & Aksu, E., (2022).
The Effects of Head Form on Resistance Performance and Flow Characteristics for A Streamlined AUV Hull Design
Ocean Engineering, vol.257, 1-13.
艦ener, M. Z., & Aksu, E., (2022).
The Numerical Investigation of The Rotation Speed and Reynolds Number Variations of A NACA 0012 Airfoil
Ocean Engineering, vol.249.
Midilli, A., K眉莽眉k, H., Hac谋osmano臒lu, M., Akbulut, U., & Dincer, 陌., (2022).
A Review on Converting Plastic Wastes into Clean Hydrogen Via Gasification for Better Sustainability
International Journal of Energy Research, vol.46, no.4, 4001-4032.听听听听听听听听听听听听听听听
T眉rk, A., Saral, D., 脰zk枚k, M., & K枚se, E., (2021).
Minimization Of Total Trim Loss Occurring in Pipe Cutting in Shipbuilding with Genetic Algorithm
Proceedings of the Institution of Mechanical Engineers Part M: Journal of Engineering for the Maritime Environment, vol.235, 695-704.听听听听听听听听听听听听听听听
脺nver, B., Altin, 陌., & G眉rgen, S., (2021).
Risk Ranking of Maintenance Activities in A Two-Stroke Marine Diesel Engine Via Fuzzy AHP Method
Applied Ocean Research, vol.111.
听听听听听听听听听听听听听听听
Nacak, C., & Sara莽, B., (2021).
The Performance Assessment of a Refrigeration System Which Exists on A Cargo Vessel Influenced by Seawater-Intake Temperature
Journal Of Thermal Analysis and Calorimetry, vol.146, no.3, 1229-1243.
Sara莽, B., (2021).
Application Of Advanced Exergy Method to The Vapour Compression Cooling Test Unit
Journal Of Thermal Science and Technology, vol.41, no.1, 157-166.
听听听听听听听听听听听听听听听
脰zmen, Y., Aksu, E., & G眉rsel 脰zmen, N., (2021).
Experimental and Numerical Investigation of Effects of Different Cavity Geometries on Flow in A Rectangular Channel
Journal Of the Faculty of Engineering and Architecture of Gazi University, vol.36, no.2, 627-640.听听听听听听听听听听听听听听听
Midilli, A., K眉莽眉k, H., Topal, M. E., Akbulut, U., & Dincer, 陌., (2021).
A Comprehensive Review on Hydrogen Production from Coal Gasification: Challenges and Opportunities
International Journal of Hydrogen Energy, vol.46, no.50, 25385-25412.听听听听听听听听听听听听听听听
T眉rk, A., & 脰zk枚k, M., (2020).
Shipyard Location Selection Based on Fuzzy AHP and TOPSIS
Journal Of Intelligent & Fuzzy Systems, vol.39, no.3, 4557-4576.
Kolukisa, D. C., Ozbulut, M., Pe艧man, E., & Yildiz, M., (2020).
Development Of Computationally Efficient Augmented Lagrangian SPH for Incompressible Flows and Its Quantitative Comparison with WCSPH Simulating Flow Past a Circular Cylinder
International Journal for Numerical Methods in Engineering, vol.121, no.18, 4187-4207.
Kara, G., & P眉r莽ek, G., (2020).
Characterization Of Boride Layer Formed on Ti-6Al-4V Alloy by Electron Beam Evaporation Technique听
Physics Of Metals and Metallography, vol.121, no.14, 1466-1472.
Kara, G., & P眉r莽ek, G., (2020).
Mechanical Properties and Cell Proliferation Response of Borided Biomedical Titanium Alloys with Different Crystalline Structures
Surface & Coatings Technology, vol.397.
听听听听听听听听
Midilli, A., K眉莽眉k, H., & Akbulut, U., (2020).
Thermodynamic Based Environmental and Sustainability Assessments of Gas Flow in A Curved Annular Channel
International Journal of Hydrogen Energy, vol.45, no.49, 26379-26386.
听听听听听听听听听听听听听听
Alt谋n, 陌., Bilgin, A., & Sezer, 陌., (2019).
Theoretical Investigation on Combustion Characteristics Of Ethanol-Fueled Dual-Plug SI Engine
FUEL, vol.257.
听听听听听听听听听听听听听听
脺nver, B., G眉rgen, S., 艦ahin, B., & Alt谋n, 陌., (2019).
Crankcase Explosion for Two-Stroke Marine Diesel Engine by Using Fault Tree Analysis Method In Fuzzy Environment
Engineering Failure Analysis, vol.97, 288-299.
听听听听听听听听听听听听听听听
Kara, G., & P眉r莽ek, G., (2019).
Boriding Behaviour of Titanium Alloys with Different Crystalline Structures
Surface Engineering, Vol.35, no.7, 611-617.听听听听听听听
听听听听听听听
K枚se, S., 脰zk枚k, M., Demirel, F. B., & K枚se, E., (2018).
Performance Indicators Considered for Selection of Agency in Maritime Industry
Transportation Journal, vol.57, no.3, 238-257.
听听听听听听听
Saral, D., Ayd谋n, M., & K枚se, E., (2018).
A Systematic Investigation of The Effects of Various Bulbous Bows On Resistance Of Fishing Boats
Brodogradnja, vol.69, 93-117.
听听听听
Yaz谋r, D., Unver, I., K枚se, E., & Bekiryazici, Z., (2018).
Modelling of Cohesive -Sediment Depositional Areas Carried by the Solakl谋 River to the Eastern Black-Sea
Indian Journal of Geo-Marine Sciences, vol.47, no.3, 721-728.
Gurgen, S., Alt谋n, 陌., & 脰zk枚k, M., (2018).
Prediction Of Main Particulars of a Chemical Tanker at Preliminary Ship Design Using Artificial Neural Network
Ships and Offshore Structures, vol.13, 459-465.
听听听听听听听
Gurgen, S., 脺nver, B., & Alt谋n, 陌., (2018).
Prediction Of Cyclic Variability in A Diesel Engine Fueled With N-Butanol and Diesel Fuel Blends Using Artificial Neural Network
Renewable Energy, vol.117, 538-544.
听听听听听听听听
艦ahin, B., G眉rgen, S., 脺nver, B., & Alt谋n, 陌., (2018).
Forecasting The Baltic Dry Index by Using an Artificial Neural Network Approach
Turkish Journal of Electrical Engineering and Computer Sciences, vol.26, 1673-1684.
https://doi.org/10.3906/elk-1706-155听听听听听听听听听听听听听听听
脟opuro臒lu, H. 陌., & Pe艧man, E., (2018).
Analysis Of Flettner Rotor Ships in Beam Waves
Ocean Engineering, vol.150, 352-362.
听听听听听听听听听听听听听听听
Alver, F., Sara莽, B., & Sahin, U. A., (2018).
Estimating Of Shipping Emissions in The Samsun Port From 2010 To 2015
Atmospheric Pollution Research, vol.9, no.5, 822-828.
听听听听听听听听听听听听听听听
Kara, G., & P眉r莽ek, G., (2018).
Growth Kinetics and Mechanical Characterization of Boride Layers Formed on Beta-Type Ti-45Nb Alloy
Surface & Coatings Technology, vol.352, 201-212.
听听听听听听听听听听听听听听听
Midilli, A., Kucuk, H., & Akbulut, U., (2018).
Exergetic Performance Comparison of Air and Hydrogen Gas Flowing Through the Annular Curved Duct听
International Journal of Hydrogen Energy, vol.43, no.23, 10859-10868.
听听听听听听听听听听听听听听听
听
Alt谋n, 陌., Bilgin, A., & Ceper, B. A., (2017).
Parametric Study on Some Combustion Characteristics in A Natural Gas Fueled Dual Plug SI Engine
Energy, vol.139, 1237-1242.
G眉rgen, S., 脺nver, B., & Alt谋n, 陌., (2017).
Experimental Investigation on Cyclic Variability, Engine Performance, And Exhaust Emissions in A Diesel Engine Using Alcohol-Diesel Fuel Blends
Thermal Science, vol.21, 581-589.
Aksu, E., Sara莽, B., & Ayhan, T., (2017).
Experimental Investigation and Computational Fluid Dynamics Analysis of Flow and Heat Transfer for Heated Plate听
Journal Of Thermophysics and Heat Transfer, vol.31, no.4, 937-946.
脰zmen, Y., & Aksu, E., (2017).
Wind Pressures on Different Roof Shapes of a Finite Height Circular Cylinder
Wind And Structures, vol.24, no.1, 25-41.
Kara, G., P眉r莽ek, G., & Yanar, H., (2017).
Improvement Of Wear Behaviour of Titanium by Boriding
Industrial Lubrication and Tribology, vol.69, no.1, 65-70.
听听听听听听听听听听听听听听听
Midilli, A., & Kucuk, H., (2017).
A Preface to The Special Issue Section On "The National Hydrogen Technologies Congress (UHTEK 2015), 20-23 December 2015, Istanbul, Turkey"
International Journal of Hydrogen Energy, vol.42, no.4, 2434.听听
Akbulut, U., Ovali, R. V., & Kucuk, H., (2017).
Viscous Dissipation Effects on Entropy Generation in Heated Vertical Parallel-Plate Channels for Mixed Convection听
International Journal of Exergy, vol.23, no.1, 1-17.
听听听听听听听听听听听听听听
听
脰zk枚k, M., (2016).
Investigation of welder selection parameters based on fuzzy analytic hierarchy process in shipbuilding
International Journal of Maritime Engineering, vol.158, 239-250.
听听听听听听
脰zk枚k, M., Ka艧谋k莽谋, M., & Helvac谋o臒lu, 陌., (2016).
Assembly Line Balancing Implementation in Minor and Sub Assembly Workshop at Shipyards.听 International Journal of Maritime Engineering, vol.158, 151-160
听听听
脟ebi, S., 脰zk枚k, M., Kafali, M., & Kahraman, C., (2016).
A Fuzzy Multiphase and Multicriteria Decision-Making Method for Cutting Technologies Used in Shipyards
International Journal of Fuzzy Systems, vol.18, no.2, 198-211.
https://doi.org/10.1007/s40815-015-0085-5听听听听听
Alt谋n, 陌., & Bilgin, A., (2016).
The Effect of Spark Advance on Engine Performance Characteristics in A Spark Ignition Engine Having Various Spark Plug Numbers and Locations听
Journal Of the Faculty of Engineering and Architecture of Gazi University, vol.31, 361-368.听听听听听听听听听听听听听听听
Kucuk, H., (2016).
Numerical study on entropy generation in L-shaped curved channels
International Journal of Exergy, vol.20, no.4, 465-481.听听听听听听听听听听听听听听听
Ugurlu, O., Yildirim, U., Yuksekyildiz, E., Nisanci, R., & K枚se, E., (2015).
Investigation Of Oil Tanker Accidents by Using GIS
International Journal of Maritime Engineering, 113-124.
听听听听听听听听
Ugurlu, O., K枚se, E., Yildirim, U., & Yuksekyildiz, E., (2015).
Marine accident analysis for collision and grounding in oil tanker using FTA method听
Maritime Policy & Management, vol.42, no.2, 163-185.
脰zk枚k, M., (2015).
Work Analysis of Plate Bending Workshop in Shipbuilding Industry
International Journal of Maritime Engineering, vol.157, 275-283.
听
脰zk枚k, M., (2015).
Risk Evaluation of Pin Jig Work Unit in Shipbuilding by Using Fuzzy AHP Method
Brodogradnja, vol.66, no.1, 39-53.听听
Kafali, M., & 脰zk枚k, M., (2015).
Evaluation of shipyard selection criteria for shipowners using a fuzzy technique
Journal Of Marine Engineering and Technology, vol.14, no.3, 146-158.
Alt谋n, 陌., & Bilgin, A., (2015).
Quasi-dimensional modeling of a fast-burn combustion dual-plug spark-ignition engine with complex combustion chamber geometries
Applied Thermal Engineering, vol.87, 678-687.听听听听听听听听听听听听听听听
Pe艧man, E., Kolukisa, D. C., & Taylan, M., (2015).
Numerical And Analytical Approaches for Roll Motion Analysis in Regular Longitudinal Waves
Polish Maritime Research, vol.22, no.3, 28-35.听听听听听听听听听听听听听听听
Sarac, B., (2015).
Exergy analysis in the withering process for Turkish black tea production
International Journal of Exergy, vol.18, no.3, 323-339.
听听听听听
Kara, G., P眉r莽ek, G., Atasoy, Y., & Bacaksiz, E., (2015).
Microstructure And Tribological Properties of Ti Borided by Electron Beam Evaporation Technique
Journal Of the Balkan Tribological Association, vol.21, no.1, 24-37.听听
Midilli, A., & Kucuk, H., (2015).
Assessment of exergetic sustainability indicators for a single layer solar drying system
International Journal of Exergy, vol.16, no.3, 278-292.
听听听听听听听听听听听听听听听
Kafali, M., 脰zk枚k, M., & Cebi, S., (2014).
Evaluation Of Pipe Cutting Technologies in Shipbuilding
Brodogradnja, vol.65, no.2, 33-48.听听听听听听听听听
脰zk枚k, M., (2014).
Risk Assessment in Ship Hull Structure Production Using FMEA
Journal Of Marine Science and Technology-Taiwan, vol.22, no.2, 173-185.
听听听听听听
脟ebi, S., 脰zk枚k, M., & Demirci, E., (2014).
Evaluation of Design Parameters for Vessel Engine Room by Using a Modified QFD Technique
Journal Of Multiple-Valued Logic and Soft Computing, vol.23, no.5, 559-587.听听听听听
脰zk枚k, M., & Cebi, S., (2014).
A fuzzy based assessment method for comparison of ship launching methods听
Journal Of Intelligent & Fuzzy Systems, vol.26, no.2, 781-791.听
Bali, T., & Sarac, B. A., (2014).
Experimental investigation of decaying swirl flow through a circular pipe for binary combination of vortex generators
International Communications in Heat and Mass Transfer, vol.53, 174-179.
听听听听听听听听听听听听听听
艦ahin, Z., Tuti, M., & Durgun, O., (2014).
Experimental investigation of the effects of water adding to the intake air on the engine performance and exhaust emissions in a DI automotive diesel engine
FUEL, vol.115, 884-895.听听
Kucuk, H., Midilli, A., Kilic, A., & Dincer, I., (2014).
A Review on Thin-Layer Drying-Curve Equations
Drying Technology, vol.32, no.7, 757-773.
Ozkok, M., (2013).
Effects Of Welding Operating Factor on Shipyard Panel Line's Production Quantity
Scientia Iranica, vol.20, no.6, 1773-1780.
Ozkok, M., (2013).
The Effects of Machine Breakdown on Hull Structure Production Process
Scientia Iranica, vol.20, no.3, 900-908.
Özkök, M., & Helvac谋o臒lu, 陌. H., (2013).
A Continuous Process Improvement Application in Shipbuilding
Brodogradnja, vol.64, no.1, 31-39.
Özkök, M., & Helvac谋o臒lu, 陌. H., (2013).
Determination of the Effects of the Pre-Outfitting and Pre-Piping Assembly Operations on Shipyard Productivity
Polish Maritime Research, vol.20, no.1, 59-69.
Özkök, M., (2012).
The Effects of Matrix Module Structure on Shipyard Panel Line's Throughput
Polish Maritime Research, vol.19, no.3, 65-71.
Pesman, E., & Taylan, M., (2012).
Influence Of Varying Restoring Moment Curve on Parametric Roll Motion of Ships In Regular Longitudinal Waves
Journal Of Marine Science and Technology, vol.17, no.4, 511-522.
Karakas, S. C., Ucer, E., & Pe艧man, E., (2012).
Control Design of Fin Roll Stabilization in Beam Seas Based on Lyapunov's Direct Method
Polish Maritime Research, vol.19, no.2, 25-30.
Midilli, A., Küçük, H., & Dincer, I., (2012).
Environmental And Sustainability Aspects of a Recirculating Aquaculture System
Environmental Progress & Sustainable Energy, vol.31, no.4, 604-611.
Saraç, B., Al-Madani, H., & Ayhan, T., (2011).
Heat Transfer from A Short Plate Behind an Obstacle in Tandem
Energy Conversion and Management, vol.52, no.10, 3147-3158.
Kucuk, H., (2011).
Numerical Analysis of Entropy Generation and Minimisation in Eccentric Curved Annular Ducts
International Journal of Exergy, vol.9, no.1, 40-65.
Guneroglu, A., Kose, E., Karsli, F., & Feyzioglu, M., (2010).
Intercomparison And Usage of Different CHL-A Algorithms and In-Situ Validation of Oc3m In Continental Shelf Waters Of The Black Sea
Fresenius Environmental Bulletin, vol.19, no.3, 452-460.
Kurto臒lu, 陌. Z., Kucuk, H., Alkan, A., & Ozdemir, A., (2010).
Economic Analysis and Sustainability of Turkish Marine Hatcheries
Turkish Journal of Fisheries and Aquatic Sciences, no.4, 513-521.
Kucuk, H., (2010).
Numerical analysis of entropy generation in concentric curved annular ducts
Journal Of Mechanical Science and Technology, vol.24, no.9, 1927-1937.
Kucuk, H., Midilli, A., Özdemir, A., Cakmak, E., & Dincer, I., (2010).
Exergetic performance analysis of a recirculating aquaculture system
Energy Conversion and Management, vol.51, no.5, 1033-1043.
Kucuk, H., & Gedikli, H., (2010).
Natural Convection in A Triangular Cross Section Roof Under Daylight Conditions
Journal Of Thermal Science and Technology, vol.30, no.1, 99-110.
Alt谋n, 陌., & Bilgin, A., (2009).
A parametric study on the performance parameters of a twin-spark SI engine
Energy Conversion and Management, vol.50, 1902-1907.
Bilgin, A., Alt谋n, 陌., & Sezer, 陌., (2009).
Investigation of the Effect of Dual Ignition on the Exhaust Emissions of an SI Engine Operating on Different Conditions by Using Quasi-Dimensional Thermodynamic Cycle Model
Strojarstvo, vol.51, no.5, 459-464.
Alt谋n, 陌., Sezer, 陌., & Bilgin, A., (2009).
Effects of the Stroke/Bore Ratio on the Performance Parameters of a Dual-Spark-Ignition (DSI) Engine
Energy & Fuels, vol.23, 1825-1831.
Sezer, 陌., Alt谋n, 陌., & Bilgin, A., (2009).
Exergetic Analysis of Using Oxygenated Fuels in Spark-Ignition (SI) Engines
Energy & Fuels, vol.23, 1801-1807.
Kucuk, H., Avci, M., Aydin, O., & Asan, H., (2009).
Analysis Of Heat and Fluid Flow in Concentric Annular Square Ducts
Journal Of Thermal Science and Technology, vol.29, no.1, 7-13.
Kucuk, H., & Asan, H., (2009).
Forced Convection Heat Transfer in Eccentric Curved Annular Square Ducts
Journal Of Thermal Science and Technology, vol.29, no.1, 67-78.
Kucuk, H., & Asan, H., (2009).
A Numerical Study on Heat and Fluid Flow in Concentric Curved Annular Square Ducts
Heat Transfer Engineering, no.5, 383-392.
Dinçer, A. C., & Bahar, M., (2008).
Multifilament Gillnet Selectivity for The Red Mullet (Mullus Barbatus) In the Eastern Black Sea Coast of Turkey, Trabzon
Turkish Journal of Fisheries and Aquatic Sciences, vol.8, no.2, 355-359.
Sivri, N., Erturk, A., & Köse, E., (2008).
The Effects of a Fish Farming Scenario Using QUAL2E Modelling at Firtina Creek (Black Sea Region)
Turkish Journal of Fisheries and Aquatic Sciences, vol.8, no.2, 293-300.
Bali, T., & Sarac, B., (2008).
Exergy analysis of heat transfer in a turbulent pipe flow by a decaying swirl generator
International Journal of Exergy, vol.5, no.1, 64-77.
Sarac, B. A., & Bali, T., (2007).
An Experimental Study on Heat Transfer and Pressure Drop Characteristics of Decaying Swirl Flow Through a Circular Pipe with A Vortex Generator
Experimental Thermal and Fluid Science, vol.32, no.1, 158-165.
Ayhan-Sarac, B., Karlik, B., Bali, T., & Ayhan, T., (2007).
Neural Network Methodology for Heat Transfer Enhancement Data
International Journal of Numerical Methods for Heat & Fluid Flow, Vol.17, 788-798.
Asan, H., & Kucuk, H., (2007).
A Numerical Computation of Heat and Fluid Flow In L-Shaped Curved Channels
Heat Transfer Engineering, no.2, 112-119.
Zengin, M., & Dinçer, A. C., (2006).
Distribution And Seasonal Movement of Atlantic Bonito (Sarda Sarda) Populations in The Southern Black Sea Coasts
Turkish Journal of Fisheries and Aquatic Sciences, vol.6, 57-62.
Sivri, N., Kose, E., & Feyzioglu, A. M., (2006).
Modelling The Effects of Industrial Discharged Waters to Degirmendere River (Southeastern Black Sea)
Journal Of Scientific & Industrial Research, vol.65, no.8, 632-638.
Basar, E., Kose, E., & Guneroglu, A., (2006).
Finding Risky Areas for Oil Spillage After Tanker Accidents at Istanbul Strait
International Journal of Environment and Pollution, vol.27, no.4, 388-400.
Guneroglu, A., Kose, E., Eruz, C., Basar, E., Erkebay, S., & Karsli, F., (2005).
Use Of Geographic Information System (GIS) To Select Fish Cage Farming Sites in Surmene Bay, Black Sea
Israeli Journal of Aquaculture-Bamidgeh, vol.57, no.2, 81-89.
Kose, E., Basar, E., Demirci, E., Guneroglu, A., & ERKEBAY, S., (2003).
Simulation Of Marine Traffic in Istanbul Strait
Simulation Modelling Practice and Theory, vol.11, 597-608.
Kose, E., Eruz, C., Guneroglu, A., Erkebay, S., & Gulten, Y., (2003).
Simulation Of Coastal Currents and River Discharges in The South-Eastern Black Sea
Indian Journal of Marine Sciences, vol.32, no.3, 194-201.
Midilli, A., & Kucuk, H., (2003).
Energy And Exergy Analyses of Solar Drying Process of Pistachio
Energy, no.6, 539-556.
Midilli, A., & Kucuk, H., (2003).
Mathematical Modeling of Thin Layer Drying of Pistachio By Using Solar Energy
Energy Conversion and Management, no.7, 1111-1122.
Midilli, A., Kucuk, H., & Yapar, Z., (2002).
A New Model for Single-Layer Drying
Drying Technology, no.7, 1503-1513.
